The FMB204 is a Teltonika FMB204 tracker with a pre-installed SIM and GNSS and GSM connectivity, that is made in the EU. It uses the Trackserver phone app, and trackserver.ie web-app.
It uses 2G networks, which unlike 3G which is gone, 2G is going to be around for many more years (2033 at least) because the IOT / metering workplace relies on it.
It comes ready to use when powered on. It has a 15mm square internal ceramic GPS antenna and 10 conductor cable. It does not need a wiring kit.
It has onboard memory for data collection following GPRS network disconnection.
Its compact size allows it to be easily placed or hidden. It needs connection to always-on power ideally located in a place with strong satellite signal reception to prevent high power consumption.
It has a significant internal Li ion battery, 1800mAh which charges in 90mins. It provides a battery life, of ca. 5 days, standalone or after disconnection of external power.
Recommended installation is to (only) use the red and black leads connecting to vehicle (always) positive and (always) earth respectively. Using a digital output (e.g. DOUT1) to install / operate a fuel cut-off fuel pump relay needs to be installed only by appropriately qualified technicians. Because many undesirable outcomes can result from vehicle immobilisation, we disclaim responsibility for consequences.
The printed face (front) of the tracker covers the antennae, and so must be orientated towards the sky / road /interior to optimise satellite radio signal reception.

Summary
The Teltonika FMB204 has two main modes of operation - Normal mode and Deep Online Sleep mode. It is an exceptionally flexible tracker with many alerting options available through its many digital & analog inputs and outputs.

General characteristics
Weight:  176g and 214g including packaging. Does not come with a charger.
Dimensions:  Length=88mm (including cable gland); Width=73mm; Thickness=38mm. Cable (10 strand) length ~83cm.
Battery:  Lithium polymer (LiPo) 1800mAh 3.7V has a battery liife of about 5 days autonomous power. Battery may require connection when delivered.
Charging voltage: 6 - 30Vdc
Antennas and Status/Navigate LEDs are on printed side, which needs be installed facing the outside world, to favour satellite signal reception.


Characteristics
Quad-band operation 900/1800MHz (Most of world) 850/1900MHz (Americas)
Integrated GNSS receiver - Cold start: 35s (unobstructed sky), Warm start: 25s, Hot start: 1s (already on)
GPRS class 12, and up to -162dBm GNSS receiver sensitivity and jamming detection
Over-voltage protection with 34V turn off
Built-in GNSS and GSM antennas, Bluetooth 3.0 and movement sensor
2 LEDS indicating Navigate and Modem status.
Tracking: 33/99 acquisition channels. -165dBm sensitivity,  NMEA-183 protocol
GPS, GLONASS, GALILEO, BEIDOU, SBAB, QZSS, DGPS
Accuracy(hot): <3m
On-board data cache for when GSM/GPRS connection is lost.

Interfaces
DIN1 Digital Input 1 - Ignition - Yellow
DIN2 Digital Input 2 - White/Green
DIN3 Digital Input 3 - White
AIN1 Analog Input 3 - Grey
DOUT1 Digital Output 1 - White/Orange
DOUT2 Digital Output 2 - Violet
1-Wire Data - Green
1-Wire Power - Blue

+ve Power supply - Red
-ve/Gnd Ground - Black
Built in accelerometer
Internal backup battery
Power supply: +6 to 30 VDC with overvoltage protection
Internal High Gain GNSS antenna
Internal High Gain GSM antenna

Remote access from TrackServer interfaces allows users to:

• set the frequency for position reporting;
• define a Geo-Fence zone(s) and turn them On/Off; 
• turn On/Off (Arm/Disarm) the Motion detecion function
• send commands (SMS) to the tracker to change settings;
• to set contact details of the alert recipients.
• view battery level.

The large screen user interface - use the TrackServer web-app.  For small screens use TrackServer phone app, or use the small screen Web-app.

Certifications:

CE; Anatel; EAC; E25

The FMT100 is an IP65 Teltonika GPS tracker with a pre-installed SIM intended for direct attachment to battery terminals. It uses the Trackserver phone app, and trackserver.ie web-app.
It is ideal for, and designed for vehicles of any description, especially for insurance telematics, car hire, rental/leased vehicles, taxi, courier services, etc.
It comes ready to use when connected to power. It has a huge 35x35mm square internal ceramic GPS antenna and 2 40cm long pre-crimped U terminals for battery connection.
Installation could not be easier - just loosen the battery clamp screws and slide the red or black connector into place, then re-tighten.
It has an internal step-down 10-30V voltage adaptor, and a small internal Li ion 170mAh battery to allow short periods of disconnection. The battery over-voltage protection turns on at 34V, with the tracker turning off.
It has onboard memory for data collection (Flash 128MB for 422,400 records) and upload following GPRS network disconnection/re-connection.
It has a 3M VHB double-sided adhesive foam tape on its back to adhere to a suitable surface. The mounting location needs to allow for the best possible reception of satellite radio signals to prevent high power consumption. This is not always easy in a battery compartment. It is a compact size and should fit almost anywhere.
Like any Teltonika device, it can connect by Bluetooth to external devices and Low Energy sensors, such as Temperature sensors, and report in this data along with GPS information.
Like any Teltonika device, it can not only detect a collision. If so configured, on a Telematic platform, it can be made to report in "Crash Trace Data" which is accelerometer data during (up to) the 15 secs before & after a collision event at 100Hz (100 accellerometer values per second) to allow re-visualisation of the incident. Teltonika have special software tools to help do this. If you require this option, you need to let us know at time of order.
The printed face (front) of the tracker covers the 2 antennae, and flashing LEDs, which may need to be covered to conceal the LEDs and obscure its purpose/function. A 4x8cm label would cover its technical properties/branding, with a possible inscription describing it as a battery conditioner, or suchlike.
Teltonika devices are manufactured in the EU (Lithuania).

Link to Installation video:  INSTALLATION VIDEO   https://youtu.be/oqhC6J5uXlY

Summary
The Teltonika FMT100 has two available modes of operation - Normal operation (28mA) and Deep online Sleep (7mA) modes. It is an exceptionally flexible tracker with many alerting options available through based on configurable scenarios, including motion via its internal accelerometer and its Bluetooth 4.0 communication interface.

Crash/Collision Detection   CrashTraceData   

Summary

The Teltonika GH5200 Lone Worker ID Badge holder is a GPS tracker / Fall-detector /emergency call device for isolated, remote or unsupervised lone people.It uses the TrackServer platform, that combines the GPS functionality with many other optional capabilities:

• FALL (Man-Down) detector (x msecs of free fall and/or badge orientation change)
• NO MOVEMENT (possible incapacity of Wearer) detection
• AMBER ALERT (e.g. when return from a call/visit is overdue, possibly due to anti-social behaviour)
• QUARANTINE VIOLATION detector - for Covid Isolators, or Offenders on parole
• SOCIAL DISTANCING detecion (detects whether less than 2m (COVID) from another Badge)
• PANIC / SOS button to: Single-Click panic button to send an SMS alert to 1 or more people; or Double-Click to initiate a phone call to someone.
• EMERGENCY CALL option
• ID BADGE HOLDER. - We can print names and basic contact on ID Cards.

It has the capability to make an emergency call to up to 5 numbers (in sequence), and/or automated SMS messages to up to 10 people/numbers. It is for emergency calls, not regular phone use.
It can be configured either by USB cable connection, Bluetooth, SMS, or over the air FOTA-Web.

Falls can be defined in terms of time (msecs) in free-fall or in a change of angle relative to when normally worn - vertical (portrait), or horizontal (landscape). It can respond automatically to both free-fall time and badge angle change.
It can also detect and alert after the passage of a pre-specified time duration without any movement of the badge or its wearer, suggesting Incapacitation!
It is also capable of detecting social distancing (e.g. 2m rule) proximity violations in pandemic contexts. The distance between it and other similar badges, can be constantly monitored, so as to emit an audio warning when a set minimum seperation has been violated. Its records can hence greatly assist in the tracing close contacts (video available) following infection. This might be relevant again in the future if controls return.
The Teltonika GH5200 has two available modes of operation - the Normal operation and the Deep online Sleep mode to preserve battery power.
It is an exceptionally flexible tracker with many alerting options available. It has an reasonable battery size (1050mAh) and life (2-3 day). Daily overnight re-charging should probably be standard if possible.

Although capable of many uses, it is very simple to use. What it does is determined by the Configuration file loaded onto it. GPS2Find can help customers tune the config file to a customer's particular objectives. These configs can be further changed by sending a different one over the air or by Bluetooth.
We do also supply simpler  PERSONAL welfare/safety trackers. Follow these linksto:  -the A21 & FA29 Pendants; or to: the  A20S & FA27T Watches.

It also requires the purchase and annual renewal of a subscription -SubPerson-12m. Quantity discounts are available - see Price reductions tab above.

Button Functions:
The front of the badge is designed to hold a standard ID card (credit card size 86 x 54mm) The back of the GH5200 has 5 buttons which come with default function assignments that cover the most popular needs. These can be altered, over the air, to match other customer requirements, also by sending the Badge a revised configuration file using a web-FOTA (Firmware Over The Air) interface.
Configuration can be done either by GPS2Find for its customers, or through the training of a customer appointee to do this - by special arrangement. Contact numbers for emergency calls of SMS alerts can be defined in the TrackServer Settings section.
A list of the potential functions that can be assigned to the 5 buttons is contained in a document referenced below. Each button has functions attached to: SINGLE CLICK; DOUBLE CLICK; and LONG CLICK. Button 1 has the default function to turn GPS tracking On and Off to allow the Wearer privacy after working hours! See Function Button Options List.

The GH5200 has GPS/GNSS, GSM and Bluetooth connectivity:

1. Two - way voice communication for emergency calls.
2. Slim lightweight design suitable for everyday use.
3. Bluetooth for external devices and linkage to Low Energy sensors
4. Man-Down, Panic, Alarm & No Movement scenarios
5. 5 buttons that can be configured to a range of functions
6. Up to 5 Call/SMS recipients in case of emergency event

It is designed for anyone who performs activity without the close or direct supervision of others. It represents the use of a latest technology to give psychological assurance and mitigate the risks and fears faced by lone workers, such as:

1. Healthcare or Social visitors,
2. Maintenance Technicians/Engineers/Workers,
3. Lone workers who work isolated from others (e.g. BS 8484:2016 capabilities)
4. Home or gig-economy workers/drivers
5. Employees working out of standard working hours 24/7.
6. Agriculture or Forestry workers

The tracker offers high quality voice communication, programmable LED indications and a 1050mAh rechargeable battery, and USB Micro charging lead, to meet latest legislation for lone workers safety and protection. They provide a system by which business managers can fulfil legal and moral obligations to keep in touch with such workers and respond to any incidents. ID Cards (credit card size: 86 x 54 mm) can be inserted, for either landscape or portrait lanyard (not included) attachment. It is a 2G device, and so should be operational until 2030 at least.

General characteristics

Charging voltage: 5 Vdc
Antennas and Status/Navigate LEDs are on the ID card side, which needs be orientated facing the outside world, to favour satellite signal reception.
 

Remote access from the TrackServer phone app and trackserver.ie web-app interfaces allows users to:

• set the frequency for position reporting;
• define a Geo-Fence zone(s) and turn zones On/Off; 
• turn On/Off (Arm/Disarm) the Motion detecion function
• send commands (SMS) to the tracker to change settings;
• to set contact details of the alert recipients.
• view battery level.

The large screen user interface - use the TrackServer web-app.  For small screens use TrackServer phone app, or use the small screen Web-app.

A Charging Rack accessory for holding 10 Worker Badges while being charged (usually overnight) is available.

External Docs / Links:
Social Distancing Video
Datasheet Link
First Start Manual Link
GH5200 Parameter List
Function Button Options List

Certifications: (webpage links)

GH5200 CE RED
GH5200 EAC
GH5200 Ukrainian UCRF
GH5200 Anatel
GH5200 FCC
GH5200 UKCA

Declarations: (webpage links)

GH5200 RoHS
Declaration of IMEI assignment
Declaration of IMEI security
REACH Regulation Declaration
Declaration of Conformity to BS8484:2016, Section 5

The FMB965 is the successor to the FMB920 with a bigger internal battery (1200mAh) and improved housing, with a pre-installed SIM, is EU made, and has GNSS and GSM connectivity. It is ideal for motorcycles.
It uses the Trackserver app and trackserver.ie web-app, if telematic data is not required.
It comes ready to use when powered on. It has a 25mm square internal ceramic GPS antenna and a 5 conductor cable for 1 Digital Input & 2 Digital outputs. It does not need a wiring kit.
It comes with a 128MB memory on-board for data collection/caching when the GPRS network is lost, then uploads when reconnected.
Its compact size and IP67 body (with cable attached) allows it to be easily placed or hidden on motorbikes, jetskis, snowmobiles, boats, SUVs, etc.
Recommended installation uses the red (10-30Vdc) and black leads connecting to vehicle (always) positive and (always) earth respectively. Using the Digital inputs to operate a fuel supply cut-off relay should only be done by a qualified person.
The printed face (front) of the tracker covers the antennae, and so must be orientated towards the sky / road /interior for satellite radio signal reception.

Operating mode
The Teltonika FMB920 has two available modes of operation - Normal operation and Deep online Sleep modes.

General characteristics
Weight:  58g and 241g including packaging. Does not come with a charger.
Dimensions:  Length=79mm; Width=43mm; Thickness=12mm
Battery:  Lithium polymer (LiPo) 1200mAh 3.7V is small with a short battery liife of about 4 days autonomous power.
Charging voltage: 6 - 30Vdc


Characteristics
Quad-band operation 900/1800MHz (Most of world) 850/1900MHz (Americas)
Integrated GNSS receiver - Cold start: 35s (unobstructed sky), Warm start: 25s, Hot start: 1s (already on)
GPRS class 12, and up to -162dBm GNSS receiver sensitivity and jamming detection
Over-voltage protection with 34V turn off
Built-in GNSS and GSM antennas, Bluetooth 3.0 and movement sensor
2 LEDS indicating Navigate and Modem status.
Tracking: 33/99 acquisition channels. -165dBm sensitivity,  NMEA-183 protocol
GPS, GLONASS, GALILEO, BEIDOU, SBAB, QZSS, DGPS
Accuracy(hot): <3m
Internal 128MB SD card to store data cached when GSM/GPRS connection is lost.

Interfaces
1 Digital Input - Yellow
1 Analog Input - Grey
1 Digital Open-collector Output (connecting external relays, LED, buzzers etc.) - White
+ve Power supply - Red
-ve/Gnd Ground - Black
Built in accelerometer
Internal backup battery
Power supply (+6…+30) V DC with overvoltage protection
Internal High Gain GNSS antenna
Internal High Gain GSM antenna

Remote access from TrackServer interfaces allows users to:

• set the frequency for position reporting;
• define a Geo-Fence zone(s) and turn them On/Off; 
• turn On/Off (Arm/Disarm) the Motion detecion function
• send commands (SMS) to the tracker to change settings;
• to set contact details of the alert recipients.
• view battery level.

The large screen user interface - see TrackServer-Desktop for more detail.  For small screen (phone app) mobile access and control use the TrackServer iOS App orAndroid App, or use the small screen Web-app.

Certifications:

CE; Anatel; EAC; E25

The TMT250 is a Teltonika TMT250 tracker with a pre-installed SIM and GNSS and GSM connectivity and waterproof IP67 ingress protection, made in the EU (Lithuania).
It can detect a Fall (Free fall or Orientation angle change), SoS button, and/or No Movement detection, making it suited to Lone Worker use.
It uses the Trackserver phone app, and trackserver.ie web-app.
It comes ready to use when powered on. It has a 18x18mm square internal ceramic GPS antenna under the top (blue button) surface.
It has onboard memory for data collection following GPRS network disconnection.
Its compact size allows it to be easily placed or hidden. It needs to be located in a place with strong satellite signal reception to prevent high battery power consumption.
It has a modestly sized internal Li ion battery, 800mAh which charges in ~40mins. It provides a battery life, of ca. 1 day standalone and so needs daily overnight charging.
There is an ankle-fastening accessory bracelet - TMT250Ankle for un-removable attachment to a person. Cutting or removing it can be set to lead to an alert message.

Summary
The Teltonika TMT250 has two available modes of operation - Normal operation and Deep online Sleep modes.
It is an exceptionally flexible tracker with many alerting options available.

General characteristics
Weight:  41g and 77g including packaging, which includes a magnetic 4-pole to USB-A charging lead.
Dimensions:  Length=44mm (including cable gland); Width=43mm; Thickness=20mm.
Battery:  Lithium polymer (LiPo) 800mAh 3.8V 3.04Wh has a battery liife of about 1 day autonomous power. Battery is connected, and SIM fitted when delivered.
Charging voltage: 5Vdc
Antennas and Status/Navigate LEDs are on blue button side, which needs be installed facing the outside world, to allow satellite signal reception.
Alert notification: LED and vibration.

Software:
Trackserver phone app, and trackserver.ie web-app.
Configuration and firmware update: FOTA WEB (cloud based solution), Teltonika Configurator (USB, Bluetooth), Configuration through SMS
Alert Scenarios: Alarm button, Man-down detection, Home zone, Inside tracking, Movement/No Movement Events, 50 Manual Geofence zones, Over Speeding, Action on call feature, Real Time tracking, Smart algorithm of GPRS data sending for GPRS traffic saving, Asset tracking
Sleep modes: Online Deep Sleep is the only sleep mode enabled in Trackserver. Others available by SMS command are: Deep Sleep, Ultra Deep Sleep, Low power mode.
Protocols: UDP/TCP/SMS
Data sending: Primary, Duplicate and Backup servers
Security: Configuration password, SMS login and password, Authorized GSM numbers list, TLS
Time Synchronization: GNSS, NITZ, NTP
Supported peripherals: Bluetooth LE Movement sensors, LE Magnet sensors, LE Temperature and Humidity sensors and LE Temperature sensors support, iBeacon and Eddystone beacon support

Characteristics
Quad-band GSM operation 900/1800MHz (Most of world) 850/1900MHz (Americas)
GSM/GPRS/GNSS/Bluetooth (4.0 + LE) and GPS, GLONASS, GALILEO, BEIDOU
Integrated GNSS receiver - Cold start: 35s (unobstructed sky), Warm start: 25s, Hot start: 1s (already on)
GPRS class 12, and up to -135dBm GNSS receiver sensitivity and jamming detection
Built-in GNSS and GSM antennas, Bluetooth 4.0 and accelerometer movement sensor
Single LED indicating Navigate and Modem status and 2 configurable buttons.
Tracking: 33 channels. -165dBm sensitivity,  NMEA-183 protocol
On-board data cache for when GSM/GPRS connection is lost. Internal Micro-SIM Slot, 128 MB internal flash memory (220‘000 records)

Remote access from TrackServer interfaces allows users to:

• set the frequency for position reporting;
• define a Geo-Fence zone(s) and turn them On/Off; 
• turn On/Off (Arm/Disarm) the Motion detecion function
• send commands (SMS) to the tracker to change settings;
• to set contact details of the alert recipients.
• view battery level.

The large screen user interface - use the TrackServer web-app at trackserver.ie.  For small screens use TrackServer phone app, or the small screen web-app at mobile.trackserver.co.uk Link: small screen Web-app.

Certifications/Regulatory:  CE/RED; Anatel(pending); EAC; RoHS, REACH, E25, UKCA(pending). 

The TMT100 is a long-lasting stand-alone (Backup) Teltonika GPS tracker with pre-installed SIM. It can function as a backup tracker to another, detecting by Bluetooth when the primary tracker has been disabled - double protection.
It has waterproof IP68 ingress protection, and is made in the EU (Lithuania). It has a removable end-face plug. See below
By being configured to report once per day, its slow discharge Lithium thionyl chloride (LiSOCl2) internal battery (7.2V 2200mAh / 15.84Wh), can last up to 3 yrs. There is an internal On/Off switch.
Its batteries are swappable, not re-chargeable. Battery replacement is very simple - pull out end-cap, slide out the main circuit board, unclip batteries & unplug (Molex connector) the battery. No soldering required.

It is capable of serving as a Backup tracker,
It uses the Trackserver phone app, and trackserver.ie web-app.
It comes ready to use when powered on. It has a 25x25mm square internal ceramic GPS antenna under the top (printed) surface.
It has onboard memory for data collection following GPRS network disconnection, with 128 MB internal flash memory (220,000 records).
As it is wireless, it can be placed / hidden in a wide range of locations usually. Its top (printed) face needs to receive satellite signal to avoid high battery power consumption.

It is an exceptionally flexible tracker with many alerting options available.

General characteristics
Weight: 110g, 155g incl. box .
Casing has 4 tie-attachment loops/slots
Dimensions:  Length=78mm; Width=63mm; Thickness=28mm.
Battery: Extremely low self-discharge Li-SOCl2 swappable battery, 7.2V 2200mAh (15,84Wh)
Charging voltage: not applicable.
Antennas are both under the top printed surface.
Status/Navigate LEDs: none.
Alert notification: SMS or email through Trackserver app.
Interface: Ultra-low-power Bluetooth BlueNRG-232 chipset, 2.0 micro-USB, Internal micro-SIM slot.
GNSS: GPS, GLONASS, GALILEO, BEIDOU, SBAS, QZSS, DGPS, AGPS
Cellular: Quad-band GSM 850 / 900 / 1800 / 1900 MHz; GPRS Multi-Slot Class 12 (up to 440 kbps); GPRS Mobile Station Class B
External: Bluetooth Sensors (up to BLE 5.0)

Software:
Trackserver phone app, and trackserver.ie web-app.
Configuration and firmware update: FOTA WEB (cloud based solution), Teltonika Configurator (USB, Bluetooth), Configuration through SMS
Alert Scenarios: Enhanced tamper detection, Accelerometer wake up, GNSS and LBS, Indoor Tracking, Bluetooth sensor support (Light, Temperature, Humidity, etc.), Recover mode, Movement detection, Scheduler with time zones, Tracking on stop / on move, Backup Tracking, Static navigation
Sleep modes: Online Deep Sleep is the only sleep mode enabled in Trackserver. Others available by SMS command are: Deep Sleep, Ultra Deep Sleep, Low power mode.
Protocols: UDP/TCP/SMS
Data sending: Primary, Duplicate and Backup servers
Security: Configuration password, SMS login and password, Authorized GSM numbers list, TLS
Time Synchronization: GNSS, NITZ, NTP
Supported peripherals: Bluetooth LE Movement sensors, LE Magnet sensors, LE Temperature and Humidity sensors and LE Temperature sensors support, iBeacon and Eddystone beacon support
Remote access from TrackServer interfaces allows users to:

• set the frequency for position reporting;
• define a Geo-Fence zone(s) and turn them On/Off; 
• turn On/Off (Arm/Disarm) the Motion detecion function
• send commands (SMS) to the tracker to change settings;
• to set contact details of the alert recipients.
• view battery level.

For large screens, use the TrackServer web-app at www.trackserver.ie
For small screens, use the TrackServer (downloadable) phone app, or the small screen web-app at mobile.trackserver.co.uk Link: small screen Web-app.
The Trackserver interface provides the Teltonika TMT100 with two available modes of operation - Normal operation and Deep online Sleep modes. Others are available by SMS command.

TAT100 Parameter list: TAT100 Parameter list
TAT100 SMS/GPRS Commands: TAT100 SMS/GPRS Commands
TAT100 First Start: TAT100 First Start
 

Certifications/Regulatory(pending)    CE(RED), EAC, RoHS, REACH. 

The G7-200 is an advanced GPS tracker in a waterproof magnetic housing containing a 20Ah (20,000mAh) 12-15 wks battery life, wireless charging and a 2G modem. Price includes a charging mat. It uses the Trackserver app and trackserver.ie web-app.
It comes with a pre-installed SIM card, and is ready to use when powered on. It has a 25mm square internal ceramic GPS antenna.
It has internal memory cache capacity for up to 10,000 position reports for when the GPRS/GSM connection is lost, with automatic upload on re-connection to phone networks.
Its compact size allows it to be easily placed or hidden. It has a IP67 waterproof housing.
Under its under-surface, it has a charging coils for wireless 5-Coil QI fast charging.
It supports 6 different operating modes that preserve the battery's charge.
It supports the range of alert options capable of messaging up to 3 contact details, as specified in the Settings page by either SMS or email. 

6 Operating modes
There is a selection of operating modes available designed to lengthen the battery life and make the tracker less locatable using a scanning tool.
The modes are:

1. Normal mode - tracker reports its location at the selected time interval when moving, and every 4hrs when not moving;
2. Eco mode - tracker powers off completely and wakens to report its location at a selected time interval (30m-24h), then powers off until next scheduled time;
3. Park mode - tracker semi-sleeps until it detects motion, whereupon it reports at a selected time interval until it detects non-motion, whereupon it semi-sleeps again;
4. Flight mode - tracker completely powers off for a specified number or hours, after which it powers on and reverts to Normal mode;
5. Pursuit mode - tracker reports its location at a selected time interval and does not stop doing so when it stops (detects non-motion)
6. Log mode - tracker logs and internally stores location information for a specified number of hours, after which it uploads the data to the server.

General characteristics
Weight:  550g, but 880g including charging mat and mains charger.
Dimensions:  Length=98mm; Width=80mm; Depth=45mm
Battery:  Lithium polymer (LiPo) 20Ah 3.7V / 12-15 weeks autonomous power.
Charging voltage: 4.75 - 5.25V
Each device comes with pre-installed PAYG subscription for immediate usage.
Quad-band operation 850/900/1800/1900MHz
Reception  - rapid: TTFF (Time To First Fix): 29s (cold start unobstructed sky), 1s (hot start - already started)
Precision: +/- 2.5m after first report when warmed up and with a strong GPS signal.
Motion detection: 3 axis accelerometer: 8g
Electrical interface: Custom 4 terminal magnetic coupling
Charger:  Mains charger included (3 pin for Ireland/UK)
On/Off button: None.
 

Remote access from TrackServer interfaces allows users to:

• set the frequency for position reporting;
• view the emergency/panic button status, if applicable; 
• define a Geo-Fence zone(s) and turn it/them On/Off; 
• turn On/Off (Arm/Disarm) the Motion detecion function
• send commands (SMS) to the tracker to change settings;
• to set contact details of the alert recipients.

For full control of the device's settings, see the How To section on TrackServer-Desktop for more detail.  For mobile access and partial control of the device's settings using the TrackServer Mobile interface, see the How To section on ...using the Track Panel-Mobile.

Certifications:

PTCRB CE Mark FCC RoHS

The FMB001 is a Teltonika (EU) GPS tracker with a pre-installed SIM intended for insertion into OBD-II port. It uses the Trackserver phone app, and trackserver.ie web-app.
It comes ready to use when plugged in. It has a 25mm square internal ceramic GPS antenna and  a wiring harness for electrical connections other than the OBD-II port. It does not need a wiring kit.
It has onboard memory for data collection (Flash 128MB for 422,400 records) and upload following GPRS network disconnection/re-connection.
Its compact size allows it to be placed or hidden almost anywhere. It needs connection to always-on power ideally located in a place with strong satellite signal reception to prevent high power consumption.
It has a very small internal Li ion battery, 170mAh which covers short term (2-3hrs) power disconnection.
Non OBD-II installation involves red and black leads only, to connect to vehicle positive and earth respectively.
The printed face (front) of the tracker covers the 2 antennae, and so must be orientated towards the sky / road /interior for satellite radio signal reception.

Summary
The Teltonika FMB001 has two available modes of operation - Normal operation (28mA) and Deep online Sleep (7mA) modes. It is an exceptionally flexible tracker with many alerting options available through based on configurable scenarios, including motion via its internal accelerometer and its Bluetooth 4.0 communication interface.

Crash Detection

General characteristics
Weight:  63 and 120 including packaging. Does not come with a charger.
Dimensions:  Length=67mm (including cable gland); Width=50mm; Thickness=25mm.
Battery:  Lithium polymer (LiPo) 170mAh 3.7V has a battery liife of about 3 hrs autonomous power.
Charging voltage: 6 - 30Vdc
Antennas and Status/Navigate LEDs are on printed side, which needs be installed facing the outside world, to favour satellite signal reception.


Characteristics
Quad-band operation 900/1800MHz (Most of world) 850/1900MHz (Americas)
Integrated GNSS receiver - Cold start: 35s (unobstructed sky), Warm start: 25s, Hot start: 1s (already on)
GPRS class 12, and up to -162dBm GNSS receiver sensitivity and jamming detection
Over-voltage protection with 34V turn off
Built-in GNSS and GSM antennas, Bluetooth 3.0 and movement sensor
2 LEDS indicating Navigate and Modem status.
Tracking: 33/99 acquisition channels. -165dBm sensitivity,  NMEA-183 protocol
GPS, GLONASS, GALILEO, BEIDOU, SBAB, QZSS, DGPS
Accuracy(hot): <3m
On-board data cache for when GSM/GPRS connection is lost.

+ve Power supply - Red
-ve/Gnd Ground - Black
Built in accelerometer
Internal backup battery
Power supply: +6 to 30 VDC with overvoltage protection
Internal High Gain GNSS antenna
Internal High Gain GSM antenna

Remote access from TrackServer interfaces allows users to:

• set the frequency for position reporting;
• define a Geo-Fence zone(s) and turn them On/Off; 
• turn On/Off (Arm/Disarm) the Motion detecion function
• send commands (SMS) to the tracker to change settings;
• to set contact details of the alert recipients.
• view battery level.

The large screen user interface - use the TrackServer web-app.  For small screens use TrackServer phone app, or use the small screen Web-app.

Certifications:

CE; Anatel; EAC; E25

The FMP100 is a Teltonika (EU) GPS tracker with a pre-installed SIM intended for insertion into a cigarette lighter socket. It uses the Trackserver phone app, and trackserver.ie web-app.
It comes ready to use when plugged in. It has a 25mm square internal ceramic GPS antenna and an auxiliary USB-A port. It does not need a wiring kit.
It has onboard memory for data collection (Flash 128MB for 422,400 records) and upload following GPRS network disconnection/re-connection.
Its compact size allows it to be placed or hidden almost anywhere. It needs connection to always-on power ideally located in a place with strong satellite signal reception to prevent high power consumption.
It has a very small internal Li ion battery, 170mAh which covers short term (2-3hrs) power disconnection.
The printed face (front) of the tracker covers the 2 antennae, and so must be orientated towards the sky / road /interior for satellite radio signal reception.

Summary
The Teltonika FMP100 has two available modes of operation - Normal operation (28mA) and Deep online Sleep (7mA) modes. It is an exceptionally flexible tracker with many alerting options available through based on configurable scenarios, including motion via its internal accelerometer and its Bluetooth 4.0 communication interface.

Crash Detection  Panic Button

General characteristics
Weight:  63 and 120 including packaging. Does not come with a charger.
Dimensions:  Length=67mm (including cable gland); Width=50mm; Thickness=25mm.
Battery:  Lithium polymer (LiPo) 170mAh 3.7V has a battery liife of about 3 hrs autonomous power.
Charging voltage: 6 - 30Vdc with over-voltage protection
Antennas and Status/Navigate LEDs are on printed side, which needs be installed facing the outside world, to favour satellite signal reception.


Characteristics
Quad-band operation 900/1800MHz (Most of world) 850/1900MHz (Americas)
Integrated GNSS receiver - Cold start: 35s (unobstructed sky), Warm start: 25s, Hot start: 1s (already on)
GPRS class 12, and up to -162dBm GNSS receiver sensitivity and jamming detection
Over-voltage protection with 34V turn off
Built-in GNSS and GSM antennas, Bluetooth 3.0 and movement sensor
2 LEDS indicating Navigate and Modem status.
Tracking: 33/99 acquisition channels. -165dBm sensitivity,  NMEA-183 protocol
GPS, GLONASS, GALILEO, BEIDOU, SBAB, QZSS, DGPS
Accuracy(hot): <3m
On-board data cache for when GSM/GPRS connection is lost.

+ve Power supply - Red
-ve/Gnd Ground - Black
Built in accelerometer
Internal backup battery
Power supply: +6 to 30 VDC with overvoltage protection
Internal High Gain GNSS antenna
Internal High Gain GSM antenna

Remote access from TrackServer interfaces allows users to:

• set the frequency for position reporting;
• define a Geo-Fence zone(s) and turn them On/Off; 
• turn On/Off (Arm/Disarm) the Motion detecion function
• send commands (SMS) to the tracker to change settings;
• to set contact details of the alert recipients.
• view battery level.

The large screen user interface - use the TrackServer web-app.  For small screens use TrackServer phone app, or use the small screen Web-app.

Certifications:

CE; Anatel; EAC; E25

The A20S ia a ready-to-wear GPS watch / tracker, with emergency call and many useful health, cardio and welfare functions. It uses the Aibeile phone app, and aibeile26.com web-app.

It has the capability to announce the time, initiate SOS calls, send geofence / safety zone messages, medication reminders, step counter and even sedentary reminders to take some exercise.

  It can also measure heart pulse rate and count exercise steps.

   Panic/SoS button  Fall Detection     2-way Call/Communication

It has phone functionality that is only available with a With Voice subscription (SIM type). Unless specified, the default watch subscription is without voice / phone functions.
When purchasing a GPS watch, it is necessary to choose an annual renewable subscriptions, with or without voice capabilities:

GPS Watch subscription - link:  Watch Subscription

GPS Watch with Voice subscription - link: Watch Subscription with Voice  which includes 5 mins talk time per month for emergency calls. It is not a mobile phone.

The A20S Watch uses the Aibeile app and Web App.

The App (for small screen devices) is called: Aibeile -  downloadable from the Apple or Play Stores

The Web App (for large screen devices) is called the GPS Tracking Station at: https://www.aibeile26.com - click link:>  aibeile26.com.
Download and read the two guidance documents linked below. Launch the Web-App, then:

• Select a language, e.g. the UK flag for the English language.
• Click on either the Account tab (for multiple watches) or the ID No. tab for single watches. Enter your Account name, or ID number from the label on the Watch outer box;
• Enter the Password specified on your GPS2Find invoice. The default Password is: 123456.
• Password change: If customers change the password assigned prior to delivery, it will only be possible for us to provide Online Support if the new password is shared with us.
• Select the "Monitor" tab.

Below are links to Training / User PDF documents to download. These explain their operation.

Aibeile phone App Guide - DOWNLOAD LINK

GPS Tracking Station Web App Guide:  DOWNLOAD LINK

A20s GPS Watch Guide: DOWNLOAD LINK

The A20S watch comes with a magnetic coupling charging cable and charger and a SIM already installed. Voice & telephony functions are with the Watch Subscription with Voice only. Excess call charges will be billed back to the customer.

Features:
1- With great waterproof ip67
2- 1.44 inch big touch screen
3- Magnetic charging
4- Highly accurate ceramic antenna
5- Real time tracking
6- Two way communication
7- Geo-fence and SOS emergency call
8- Heart rate monitoring and blood pressure
9- Fall down alert
10- Phonebook supported

Waterproof grade: IP67
Size: 49X40X14.5mm, strap:110mm
Weight:52g
Battery: 500mAh
Standby time: 4-5days
Positioning: GPS+BD+LBS+WIF